As the weather gets colder, many customers feel that it is difficult to start the car when it is cold. They have to start the car several times and the idle speed is unstable between (700-1200r / min) after starting. The acceleration is weak.

那么~這種情況是什么原因造成的呢？

So what is the cause of this situation?

將車輛放置冷卻狀態，鏈接專用電腦讀取故障碼及平穩值。進一步排查

Put the vehicle in the cooling state, link the special computer to read the fault code and stable value. Further investigation

油  汽  火。

Oil vapor fire.

拆卸火花塞及點火線圈查看后無異常，由于無缺火及單獨缸混合氣異常，說明噴油嘴無異常，用專業儀表測得 燃油低壓壓力為0.5Mpa,與標準值誤差不大，空氣流量為13.5kg/h 為正常，讀取節氣門開度時發現故障出現時開度忽大忽小，可見是由于配氣造成得，再?zèng)鲕噯?dòng)時發動機電腦會使混合氣比較濃，但不應忽大忽小。此可見 要么是在近氣過程中漏氣，要么是進氣管或氣門有積碳影響進氣效果。

After the spark plug and ignition coil are removed, there is no abnormality. Because there is no misfire and the mixture of individual cylinder is abnormal, it indicates that the fuel injection nozzle is normal. The low-pressure fuel pressure measured by professional instrument is 0.5MPa, The error with the standard value is not big. The air flow is 13.5kg/h, which is normal. When reading the throttle opening, it is found that the throttle opening changes from big to small when the fault occurs. It can be seen that it is caused by valve distribution. When the car is cooled again, the engine computer will make the mixture rich, but it should not change from big to small. It can be seen that either there is air leakage in the near air process, or there is carbon deposition in the intake pipe or valve, which affects the intake effect.

查看節氣門發現機碳不算特別嚴重，清洗后裝回，故障依舊。拆卸進氣管查看管道及氣門，發現氣門積碳嚴重，使用清洗劑將氣門及管道清理干凈后，恢復并刪除發動機調效值，試車怠速不穩得問題已經解決，但加速仍稍微不足，師傅判斷應是進氣管道內得機油積碳卡滯引起進氣歧管上DISA閥損壞，經拆卸  閥1無法正常工作  閥2 無法完全打開。更換試車后故障排除。

Check the throttle and find that the engine carbon is not particularly serious. After cleaning, install it back and the fault is still there. Remove the intake pipe and check the pipe and valve. It is found that there is serious carbon deposition on the valve. After cleaning the valve and pipe with cleaning agent, restore and delete the engine efficiency adjustment value. The problem of unstable idle speed in the test has been solved, but the acceleration is still a little insufficient. The master judges that it is the oil carbon deposition in the intake pipe that causes the disa valve on the intake manifold to be damaged, and valve 1 can not work normally after removal Valve 2 does not fully open. Troubleshooting after replacement test run.